Vacuum press

Vacuum press and - a model with a small work table size. Work table length from 1.05 to 1.60 m, width 1.40 m.

It can be used as equipment for the production of MDF furniture facades, and is also used as a vacuum press for plastic.

A full range of possibilities - working with all types of PVC film, veneer, plastic, combined bookmarks, triplex glass, artificial stone, ABS plastic, sublimation of drawings on parts coated with powder paint, production of body armor. Lots of additional options. In terms of its capabilities and configuration, it has no analogues.

1. Capabilities of the and vacuum press:

• Finishing with PVC films from 0.1 mm to 1 mm (including high-gloss): MDF facades, kitchen facades, MDF door overlays, countertops, door leaves, decorative overlays, MDF panels.
• Production of combined inserts (flat, curved and concave parts) simultaneously in one insert. This type of work is only possible on our machines.
• Veneering with natural veneer and lamination with finishing decorative materials, lamination with chipboard and fibreboard plastics (when using a membrane).
• Bonding and shaping of multi-layer products using a membrane, with or without heating.
• Production of triplex glass.
• Decorating metal products by thermal transfer (sublimation) of designs from special transfer films and papers.
• The vacuum press for plastic and produces molds for paving slabs from ABS plastic.
• Plastic cladding of kitchen countertops.
• Shaping artificial stone.
• Semi-automatic operating mode of the vacuum press and the ability to fully control the pressing process. Several operating modes of and equipment.
• The universal work table width divider is convenient for working with narrow films (less than 1.40 m), large-width bent parts and high chords. This option is available only on our machines and is included in the additional package.
• Adjusting the power of heating elements. You can smoothly start heating. The option is ideal for working with problematic films and other complex processes. This option is available only on our machines and is included in the additional package.
• Illumination inside the heating carriage is necessary for visual control of the workbench. Works even when the heating lamps are turned off. The option is included in the basic package.
• Work with wet veneer without damaging the machine. Effective removal of moisture from the system up to 1.2 liters/hour. Standard option for all Stangrad machines.
• Record high actual operating temperature of the machine - up to 220 degrees. S.
• A system for cleaning PVC film from small debris that adheres to the film due to electrostatic phenomena. The system removes up to 95% of debris. This option is indispensable for working with partial rolls. This option is based on the vortex air duct of the Zenova series. The system is included as an optional extra.

2. Energy saving:

• This type of equipment for furniture facades, unlike heating element presses, does not require warming up the table before starting work.
• There is no need to add hair dryers to the film. This significantly saves energy.
• Low pump power - only 1.5 kW/hour.
• The hot vacuum press and has a receiver option." A receiver with a volume of 205 liters is installed on the machine. Thanks to the vacuum control system, the machine has 2 operating modes - with and without a receiver. Due to the short-term operation of the pump, energy is saved on long-term bookmarks. Relevant for the production of blanks for bent facades, triplex glass, etc. The option is included in the additional package.

3. Savings of PVC film:

• Equipment for the production of MDF facades and is equipped with a universal work table length divider. This significantly saves PVC film when filling is incomplete. The option is included in the basic package and has no analogues.

4. Speed (volume):

• There is no need to warm up the work table before starting work, unlike heating element presses.
• Fast heating speed - at 20 degrees. In the room, the PVC film will heat up to 100 degrees. In just 60 seconds.
• There is no need to add hair dryers to the film. This is achieved through the design of the hot vacuum press table, a high-performance pump with very low residual pressure.
• This type of equipment for furniture facades does not require drilling through holes in the facades with a thin milling cutter. The PVC film shrinks completely without them.
• The Full Automatic option allows you to perform the pressing cycle in a fully automatic mode. The option is included in the additional package.
• The option of “quick fastening of the membrane on the upper frame” allows you to quickly remove and attach the membrane on the machine. The option is included in the additional package.

5. Components of the hot vacuum press and:

• Powerful, high-performance vacuum pump VALUE with a residual pressure of only 0.3 mbar. A filter with a polyester filter element is installed in front of the pump inlet. Moisture-resistant synthetic oil is poured into the pump.
• A motor protection circuit breaker is installed on the vacuum pump motor. It protects the electric motor from winding burnout when one of the phases in the electrical network fails.
• Double frame seal with silicone rubber.
• Special ultra-reliable heating KHT lamps with a separate warranty for a period of 3 years.
• The vacuum press for plastic and has a heating carriage equipped with ceramic insulators.
• The vacuum hot press is equipped with electronic devices from the leading domestic manufacturer - OWEN" with a separate warranty for a period of 2 years.
• The temperature sensor is a contact thermocouple that takes the temperature directly from the film. The measurement accuracy is 1% of the displayed temperature value. The thermocouple rests on the film when the upper frame is lowered, i.e. Based on the nod principle, there is no mechanical wear. Does not lose accuracy over time. We do not use contact thermocouple in a non-contact manner. This is due to the inaccuracy and inefficiency of this measurement method.
• The work table of the equipment for the production of MDF facades and is made of galvanized steel, aligned to 22 points, does not rust, the deviation of the table along the plane is no more than 0.7 mm. The table is not subject to deformation when heated.
• High-quality car painting.
• Factory build quality.

6. Warranty (vacuum press and):

• The warranty period for the and vacuum press is 1 year from the date of shipment of the equipment to the customer, or from the date of commissioning of the equipment during commissioning by our specialists.
• Warranty repairs of equipment are carried out during the warranty period by Stangrad specialists.
• After the expiration of the warranty period, it is possible to conclude a separate agreement for post-warranty repairs and maintenance of equipment.
• Consumables and components are always in stock and, if necessary, will be delivered to you as quickly as possible using courier services.
• Separate warranty for heating lamps for a period of 3 years.

7. Service:

• Before shipping the equipment, we organize a training course at the production workshop of the Stangrad company.
• We advise clients on operational issues and production technology that arise in the process of working on equipment for the production of MDF facades from the Stangrad company.

The Stangrad company sells a wide range of equipment for MDF facades. In order to find out the price of a vacuum press for and facades, as well as to buy a vacuum press and, please call: +7(8412) 233-399.